Foodstuff Wet Granulation Equipment Cutting Speed 1500 Rpm With Z Shaped Rotor Blade

Foodstuff  Wet Granulation Equipment Cutting Speed 1500 Rpm With Z Shaped Rotor Blade

Applying:

GHL high speed wet type mixing granulator is a high efficiency equipment that can mix different powder materials and granulate granule in one procedure. It is wide used for pharmaceutical industry, foodstuff industry and chemical industry, etc.The powder can be dry dry mixed and wet wet mixed in a pot and become a humid soft material, Then it is cut through high-speed crusher and become uniform granules.

The powder raw material and adhesive in a cylinder are fully mixed at the bottom to become a humid soft material. Then it is cut by high-speed cutter and become uniform granules.
Every parts of the equipment 
 
The high shear mixer is therefore the perfect partner for a Fluid Bed Dryer for optimum economy. 
Pellets can be manufactured if the vertical granulator is combined with a Spheronizer/Pelletizer for subsequent spheronization of the granules. 
Single-Pot systems also provide the facility to dry the granulate. 
For the use of organic solvents, the high shear mixer can be combined with a special vacuum system with integral solvent recovery.
Cuting and Mixing blade 
Due to the consistent modular design, the system can be configured individually and easily adapted to the constructional circumstances and specific requirements.
The heart of the Vertical Granulator is the patented Z-shaped rotor blade. This and various product-optimized chopper designs are the result of many years of successful development and cooperation with the Japanese specialist, Powrex.
Working Chamber
For non-sticky products in campaign production. Also for various processes with different accessory configurations. In this case, nozzles and additional equipment can be mounted to the lid.
For sticky products and similar processes with identical accessory configurations.
Handing device
This device can easily be integrated into horizontal or vertical product flow.
The high shear mixer can be charged manually by means of containers with lift and transporter devices (or charging stations) or pneumatically by means of suction conveyor systems.
The granulate is discharged from the working vessel into a fluid bed machine or a container, either by gravity or by means of pneumatic conveyors.
A  Rotor Mill is often used downstream in order to achieve a homogeneous granulate spectrum.
Control System
As complex as necessary, as easy to use as possible. The controls are precisely adapted to your requirements. Thanks to their standardised hardware basis, the control systems can be retrofitted  at any time, should your requirements change. 
Intuitive graphical operating system
This new state-of-the-art control system embodies a uniquely intuitive graphical operating philosophy. It is designed to be as easy to use as possible and only be as complex as absolutely necessary, helping to make the control of every process clear and safe. All information required is displayed on a generous  touch screen at all times. An animated flow diagram representation as well as an explosion-proof version are available.
 

Features:

1 The machine adopts horizontal cylinder structure. lts structure is reasonabIe.
2 Use air filled seal shaft to drive. When washing. it can be taken place with water
3 Use fluidization to granulate and the granule is near ball, lt’s flow is good.
4 Compared the traditional process. 25% of adhesive can be reduced and the laying time can be shorted.
5 The time of mixing in dry is 2 minutes and the time of granulating is 1 -4 minutes. Compared with the traditional process. 4-5 times of efficiency is raised
6 In the same sealed container, dry mixing, humidity mixing and granulating can be finished. lt is in conformity with the requirements of GMP,
7 The whole operation has strict safe and protective

Prameters:

Competitive advantage:

 
1. We have seven technicians who gets passport ready to travel all over world to offer service to you.
2. We have 24hours hot line for Technical Support.
3. We get 18hours internet line for technical support.
4. Video camera in workshop to help you adjust and solve machine problem in working situation.
5. We have Technical Support in below Country:
USA (Distributor ),Italy distributor,Britishi(Distributor),India(Distributor)

Comany info:

We are mainly produce the pharma machine,pharma packing machine,and disposable non-woven take care product machine.Our product includes capsule filling machine,tablet press machine,powder mixing machine,powder grinding machine,tablet capsule counting machine,blister packing machine,cartoning machine,labeling machine,face mask machine,shoe cover machine,bouffant cap machine,body wamer pad machine,eye warmer pad machine,sheet bed machine,non-woven sheet folding machine,non-woven slitting machine,etc all kind of non-woven product machine.